Offering you solutions
Hotline: +84 9666 03274
Email: marketing@unitekco.com
Hotline: +84 9666 03274
Email: marketing@unitekco.com
Thermal Imaging is an extremely powerful predictive and preventive maintenance tool that can help identify problems in utility generating stations and on their transmission and distribution systems. Guess how much you can tell with a single thermal image? Using thermography, these inspections help find excess heat coming from faulty fuses, defective breakers, damaged switches or loose connections. There could also be overloaded or imbalanced circuits or other issues. By using the information from these inspections, you can replace these small components or make minor adjustments that will prevent much more costly problems in the future.
Highest thermal resolution in its line. See small details in the image and discover anomalies faster. Capture details from far distance with Tele lens 2X and 4X
View Datasheet
Designed for everyday use, in the toughest industrial environments. Temp range: ≤-10 °C to 1000 °C. SuperResolution - Captures and combines 4x the data to create a 1280 x 960 (614,400 pixels) image.
View Datasheet
Wide, rotatable screen. AutoFocus. Full analysis and reporting software with access to the Fluke Connect system.
View Datasheet
Measure electricity line from up to 200m away with tele lens 4X. X4 resolution with SuperResolution. 5.7-inch responsive LCD touchscreen. A rugged thermal imager from Fluke Corporation.
View Datasheet
The ThermalSpection™ 724 system allows you to continuously monitor the temperature profile and long term thermal trends of assets within an electrical power substation remotely. The system consists of thermal and visible cameras mounted on a positioner with continuous 360° pan range and tilt range of ±45°.
View Datasheet
This system builds off the ThermoView TV40 series of thermal imaging cameras and features integrated thermal and visual sighting capabilities. The system was also designed for remote monitoring of industrial environments – such as substation monitoring or pile monitoring, among others – and provides a fully integrated thermal analysis of large areas through a single Pan and Tilt camera
View DatasheetGhi lại nhiệt độ và xác định bất thường trên dây dẫn từ khoảng cách xa với ống kính tele 4X và máy ảnh nhiệt 640x480.
Là sự kết hợp hoàn hảo để phát hiện các hư hỏng trên đường phân phối.
Rò rỉ SF6 tại cầu dao trạm biến áp 110 kV.
Giám sát thiết bị liên tục cho các trạm biến áp. Giám sát điểm nhiệt từ khoảng cách xa lên đến 150 mét. Một hệ thống có thể quản lý tới 300 trạm biến áp
Sự khác biệt giữa chất lượng ảnh nhiệt 320x240 và 640x480
Make it possible to identify your power quality and energy efficiency issues with easy and effective recording and analysis. Get every electrical parameters you need to see the full picture, even the smallest faults, enable you to troubleshoot and discover where savings are possible. Complies with IEC 61000-4-30 Class-A standards for correct evaluation of all measured values. Comes with free softwares to create detailed reports to focus in on the problem areas.
Designed to help you minimize downtime, quickly troubleshoot power quality issues and easily discover the costs of wasted energy. Advanced power quality health check, energy lost calculator, power inverter efficiency measurement, all in one single tool. Highest safety rating in industry
View Datasheet
An advanced version of Fluke 435-II, the Fluke 438-II also allows you to measure motor efficiency.
View Datasheet
Deliver easy to use three phase power measurement data for discovering sources of electrical energy waste, overloaded circuits and help you perform routine load studies. Discover when and where energy in your facility is being consumed - from the service entrance to individual circuits.
View Datasheet
Built with Fluke Connect® mobile app and desktop software compatibility give you the data you need to make critical power quality and energy decisions in real-time. Automatically capture and log over 500 power quality parameters so you have more visibility into the data you need to optimize system reliability and savings.
View Datasheet
Best tools to troubleshoot, quantify energy usage and analyze power distribution systems in a fast, easy and safe way. Logs over 500 different parameters for each averaging period. This allows you to analyze power quality in detail and to correlate intermittent events with detailed waveform data, helping to identify the root cause of disturbances.
View Datasheet
Supports quick and reliable configuration even in awkward test locations with the wireless interface that provides a window into what the instrument is recording. Captures the most important data for up to 30 days without losing the most important details.
View Datasheet.png)
Designed for analysis of utility and industrial power distribution systems, in medium- and low-voltage networks. Provides exceptional flexibility with the ability to customize thresholds, algorithms, and measurement selections. The 1760 power recorder captures the most comprehensive details on user-selected parameters.
View Datasheet
Fluke Norma Power Analyzer delivers precision measurements of 1 or 3 phase current and voltage, harmonics analysis, and Fast Fourier Transformation analysis.
View Datasheet
Reduced risk—Permanently installed voltage and current connections can be accessed without opening the panel door. Quickly connect your logger or analyzer and begin taking measurements faster than ever
View DatasheetThực nghiệm đo chất lượng điện năng & tổn thất năng lượng với thiết bị phân tích chất lượng điện năng Fluke 435-II
Thiết bị kiểm tra chất lượng điện năng và động cơ Fluke 438 II có thể giúp bạn phát hiện các vấn đề về chất lượng điện năng như sự mất cân bằng điện năng, sóng hài...
Phân tích chất lượng điện năng và kiểm toán năng lượng với thiết bị phân tích chất lượng điện năng Fluke 435-II
Phân tích & tìm nguyên nhân gây sóng hài trong hệ thống điện với thiết bị phân tích chất lượng điện năng Fluke 435-II
Ghi lại chất lượng điện ba pha và giám sát nhiễu loạn chất lượng điện bằng Fluke 1750 Power Recorder
Xem hình ảnh trực quan
Thực hiện các phép đo chất lượng điện ba pha một cách an toàn và dễ dàng hơn
Online PD testing is a method of inspecting the insulation of electric power system while the equipment remains energized and in service.
The PDiagnosticT utilizes AE, External UHF and HFCT sensors to detect, analyze and diagnose the PD signals in Power transformer
View Datasheet
The PDiagnosticM using UHF, AE and HFCT sensors to monitor, detect and diagnose PD signals in al multitude of medium and high voltage electrical equipments such as GIS, MV switchgear, power cables and transformers.
View Datasheet
Utilizes UHF and AE sensors to detect, analyze and diagnose the partial discharge signals on GIS. The signals detected are transmitted to the laptop through the processes of amplication, envelopemdetection, collection and signal pre-processing. The PDiagnostic software will exclude the disturbance signals, identify the defect type and evaluate the insulation PD condition of the GIS
View Datasheet
Designed to identify the PD signals in power cables with multiple sensors through 4 channels simultaneously.
View Datasheet
An expert version of the PDiagnosticM, which can detect, locate, analyze and diagnose PD signals inside transformers, GIS, power cables, substations and switchgear.
View Datasheet
Online detect and locate the parrtial discharge signales on cables, transformers and GIS
Continuous Online Insulation Testing for high voltage power systems. PMDT Monitor Systems represent a revolution in electric power testing. PMDT sensors and instrumentation provide the level of detail which is required for effective and effiecient diagnosis of insulation problems. Fiber optic, 3G wireless or 'braodband over copper' options. Diagnostic server units provide continuous access to data and reports from an entire network of PD sensors.
View Datasheet
Detect surface partial discharge and corona partial discharge from far distance. Pinpoint PD location on the screen with heatmap using Fluke SoundSight and SoundMap Technology.
View Datasheet
The Fluke ii910 Precision Acoustic Imager provides a safe, quick and easy way to detect and locate partial discharge at early stage (fequency range from 2kHz to 100kHz) in order to maintain high voltage equipment and prevent catastrophic events. With the SoundSight™ technology, the ii910 translates the sounds that it hears into a visual representation so that you can quickly locate problem areas.
View DatasheetWhile online measurement cannot be performed, an offline test would be neeeded. Off-line Partial Discharge Testing involves switching a circuit to disconnect it and then testing it while energised by a (usually very low frequency) test set. It allows the user to measure the cable system’s response to a specific stress level as voltages can be raised to multiples of U0. Off-line testing is useful for locating defects as noise levels are considerably lower off-line when compared to on-line. The challenge with off-line testing is that the equipment must be taken off-line and out of service
VLF-60 Cable Insulation Tester made by KEP is a very low frequency high potential tester that ensures efficient testing and fault location on medium voltage cables.
A modular diagnostic and test equipment, which is designed for testing and fault location of both LV and MV cables. The key parameters are designed flexible to satisfy customer’s specific requirements.
Giới thiệu Thiết bị kiểm tra phóng điện cục bộ PMDT
Giới thiệu Giải pháp kiểm tra phóng điện cục bộ online - PMDT Pdetector
Demo kiểm tra phóng điện cục bộ (PD) online tại trạm biến áp
Demo đo PD tủ trung thế bằng thiết bị Pdetector
Ideal test tools & monitori ng system for maintaining, troubleshooting and performance testing individual stationary batteries and battery banks used in critical battery back-up applications in data centers, telecom networks, power distribution systems and more.
Eagle Eye’s real-time Battery Monitoring Systems allow for 24/7/365 monitoring of your battery system. Monitor string voltage and current, as well as jar/cell voltage, internal/connection resistance, and temperature. All battery monitoring solutions come complete with battery management software that allows all real-time battery monitoring systems to be monitored 24 hours a day, 365 days a year via remote computer(s).
View Datasheet
Designed for measurements on stationary batteries of all types. Measure battery voltage, discharge volt, ripple voltage, temperature, intercell strap resistance. Comes together with advance functions such as meter and sequence modes, threshold and warning, autohold, autosave, comprehensive logging and Fluke Battery Management Software. Highest safety rating in the industry.
View Datasheet
LB-Series AC load banks and LB-Series DC load banks. Over 150 AC and DC load bank models are available across both product lines, providing load testing solutions for most applications. Custom AC and DC load bank solutions are also available.
View DatasheetMake sure your inveters are working properly by checking electrical waveform, input & output power quality, temperature, leakage current
Designed to help you minimize downtime, quickly troubleshoot power quality issues and easily discover the costs of wasted energy. Advanced power quality health check, energy lost calculator, power inverter efficiency measurement, all in one single tool. Highest safety rating in industry
View Datasheet
Simply select a test and the step-by-step guided measurements show you where to make voltage and current connections, while the preset measurement profiles ensure you will capture all the data you need for each critical motor-drive section—from the input to the output, the DC bus, and the motor itself.
View Datasheet
Rugged oscilloscope solution for industrial electrical and electro-mechanical equipment troubleshooting and maintenance applications. It's a truly integrated test tool, with oscilloscope, multimeter and high-speed recorder in one easy-to-use instrument. Integrate with Fluke Connect® mobile app and FlukeView® for ScopeMeter software to enable further collaboration, data analysis and archiving of critical test information.
View Datasheet
Highest thermal resolution in its line. See small details in the image and discover anomalies faster. Capture details from far distance with Tele lens 2X and 4X
View Datasheet
Designed for everyday use, in the toughest industrial environments. Temp range: ≤-10 °C to 1000 °C. SuperResolution - Captures and combines 4x the data to create a 1280 x 960 (614,400 pixels) image.
View Datasheet
Fluke PTi120 Thermal Imager is a compact pocket-sized themal camera that provides you quick temperature scans on electrical equipment, machinery, and other assets. It is the first line of defense in detection of spots that may lead to downtime.
View Datasheet
True-rms measurements for accuracy when measuring complex, non-sinusoidal waveforms. 40 mm jaw opening. Highest resolution of 1 μA, measure up to 60 A
View Datasheet
The Fluke 368 FC True-RMS leakage current clamp meter helps you measure small problems before they become large problems, all without taking equipment off line.
View Datasheet
True-rms measurements for accuracy when measuring complex, non-sinusoidal waveforms. 61 mm jaw opening. Selectable filter function removes unwanted noise
View Datasheet
The Fluke 369 FC leakage current clamp meter offers wireless data recording and trending for preventive maintenance, without taking equipment offline.
View DatasheetKiểm tra 18 ắc quy trong 3 phút với Fluke BT500 Series Máy đo và phân tích ắc quy Fluke BT500 Series giúp cho việc kiểm tra ắc quy nhanh chóng và dễ dàng hơn bao giờ hết. Kiểm tra hệ thống gồm 18 ắc quy chỉ trong vòng 3 phút
Đo điện trở tiếp xúc giữa 2 ắc quy với FLUKE BT500 Series Máy đo và phân tích ắc quy Fluke BT500 Series giúp cho việc kiểm tra ắc quy nhanh chóng và dễ dàng hơn bao giờ hết.
Kiểm tra chất lượng bộ sạc và dòng điện trong chuỗi ắc quy với Fluke BT500. Dòng máy đo ắc quy Fluke BT500 - thiết bị đo nội trở ắc quy chính xác, an toàn và nhanh chóng nhất trên thị trường.
Hướng dẫn kiểm tra ắc quy với máy phân tích ắc quy FLUKE BT500 Series. Dòng máy duy nhất có thể kiểm tra từng cell ắc quy riêng biệt, đo nội trở ắc quy, và báo kết quả bằng âm thanh.
Đập hộp Camera nhiệt Fluke PTi120 - Máy chụp ảnh nhiệt phổ nhiệt đầy đủ cho bạn dữ liệu đo đến độ phân giải hồng ngoài 120 x 90 (10.800 pixel)
Demo đo PD tủ trung thế bằng thiết bị Pdetector
It is critical for facilities to have grounded electrical systems, so that in the event of a lightning strike or utility overvoltage, current will find a safe path to earth. To ensure a reliable connection to earth, the International Electrical Testing Association specifies ground electrode testing every three years.
Test the grounding components of equipment in hard-to-reach spaces, including areas that are indoors or fully paved and do not permit driving auxiliary test stakes.
View Datasheet
Measures earth ground loop resistances using only clamps, only stakes, or one clamp and stakes. Fluke 1625-2 is able to measure earth ground loop resistances for multi-grounded systems using only current clamps. This technique eliminates the dangerous, and time consuming job of disconnecting parallel grounds, and finding suitable locations for auxiliary ground stakes. This allows you to perform earth ground tests in places you’ve not considered before, such as inside buildings, on power pylons, or anywhere you don’t have access to soil.
View Datasheet
True-rms measurements for accuracy when measuring complex, non-sinusoidal waveforms. 40 mm jaw opening. Highest resolution of 1 μA, measure up to 60 A
View Datasheet
Các phép đo True-RMS cho độ chính xác cao khi đo các dạng sóng phi tuyến. Độ mở hàm 40 mm. Độ phân giải cao nhất 1 μA, đo lên đến 60 A
View Datasheet
The Fluke 368 FC True-RMS leakage current clamp meter helps you measure small problems before they become large problems, all without taking equipment off line.
View Datasheet
True-rms measurements for accuracy when measuring complex, non-sinusoidal waveforms. 61 mm jaw opening. Selectable filter function removes unwanted noise
View Datasheet
The Fluke 369 FC leakage current clamp meter offers wireless data recording and trending for preventive maintenance, without taking equipment offline.
View Datasheet
ALCL-40 is designed to test the diagnostic of OXIDE SURGE ARRESTER. The least influence from the external magnetic field and noise by triple shielding of CT. Compliant with IEC6099-5. Enabled the measurements for 100nA resolution and harmonics current.
View DatasheetGet access to 50+ exclusive PdM & CbM assests including presentation decks, application note, videos, casestudies and more!
1. 100% Genuine, Brand New Products
2. Free Technical Support and Product Training
3. Free Shipping
For Free CbM Resource Center:
For Demo Program
Cảm ơn yêu cầu của bạn!
Chúng tôi sẽ liên hệ lại theo thông tin bạn cung cấp trong thời gian 48h. Nếu bạn cần gấp, vui lòng gọi số Hotline +84 966603274